Apex Roofing & Construction Text a photoCall 682-558-1382
Homeowner guide

Slab vs Pier and Beam Foundations: How to Tell Which You Have

Updated Oct 8, 2026 by Apex Roofing & Construction. General information for North Texas homeowners, not legal or insurance advice.

Short answerA slab foundation is concrete poured on the ground, so the floor sits close to grade and there is no crawl space. A pier and beam foundation holds the floor framing up on piers, posts, or footings, with a crawl space underneath, usually reached through vents or a small access door. Slabs are often repaired by underpinning or crack injection, while pier and beam floors are often re-shimmed, re-framed, or given added supports.

Before you can judge a foundation problem, you need to know what kind of foundation you have. The two common types in North Texas are slab foundations and pier and beam foundations. They move for many of the same reasons, but they fail in different ways and get repaired in different ways.

This guide uses the Texas Section of the American Society of Civil Engineers (ASCE) residential foundation guidelines as its main reference.

What is the difference between a slab and pier and beam?

A slab foundation (engineers say "slab-on-ground") is concrete poured directly on the soil. The floor of the house sits on the concrete.

Some slabs are reinforced with steel bar. Others are post-tensioned, which means steel cables, called tendons, run through the concrete and are pulled tight to hold it in compression. The ASCE Texas guidelines mention testing these cables and re-stressing them as repair steps, so it matters which kind you have.

A pier and beam foundation holds the floor up off the ground. In the guidelines' words, it is a structurally supported floor system on top of piers, posts, or footings. Wood beams and joists span between the supports, and there is an open crawl space under the floor.

How can I tell which foundation my house has?

Try these checks, in this order.

  1. Walk around the outside. Look along the base of the walls for small vent openings or an access door. Those lead to a crawl space, which means pier and beam. A slab house shows concrete at the base of the wall and no openings.
  2. Look at the front steps. A pier and beam floor sits higher off the ground, so there are often a few steps up to the door. A slab floor is usually closer to grade. Treat this as a clue only.
  3. Feel the floors. Wood-framed floors over a crawl space can flex or sound hollow when you walk. Slab floors feel solid everywhere.
  4. Check the garage floor. ConcreteNetwork notes that many post-tensioned slabs are stamped to alert owners and contractors (ConcreteNetwork). If you see that stamp, never let anyone cut or core the slab without locating the cables first.
  5. Read your paperwork. Your home inspection report, survey, or builder documents often name the foundation type. If you are buying, the Texas seller's disclosure form asks the seller about known foundation and slab defects and previous structural repairs (Property Code 5.008).

Some houses have both, such as a slab addition on a pier and beam house. The ASCE guidelines say an engineer should look at each part on its own and at the whole house.

What problems do slab foundations have?

Slabs sit right on the soil, so changes in the soil reach them directly. North Texas has a lot of expansive clay. The USDA describes the Texas state soil, Houston Black, as clay that shrinks and swells sharply with moisture changes and limits building in metro areas (NRCS via TWDB).

Common slab problems the ASCE Texas guidelines describe:

  • Deflection: the slab bends, so part of it sits higher or lower than the rest.
  • Tilt: the whole slab slopes one way.
  • Cracks in the concrete, brick, and drywall above.
  • Leaking plumbing under the slab, which ASCE lists as a cause of movement.
  • Tree roots drying out soil under one side.

How are slab foundations repaired?

The ASCE Texas guidelines list these slab repair methods:

MethodWhat it does
UnderpinningAdds support elements, such as piers, under the slab. The engineer's plan should show their locations, sizes, depths and materials.
GroutingFills voids to give the slab continuous support without lifting it much.
MudjackingPumps material under the slab to adjust its height.
Crack injectionEpoxy is injected into cracks about 1/32 inch and wider to restore stiffness across the crack.
Tendon stressingRe-tightens post-tensioned cables that test below their design force.
Partial rebuildRemoves and replaces damaged sections.

Two follow-up steps matter. First, when a slab is lifted, the guidelines say water and drain lines should be tested for leaks, and any leaks should be repaired. Second, floor elevations should be measured again after the work, with a copy given to the owner.

What problems do pier and beam foundations have?

Pier and beam floors respond to soil movement too, but they also have problems a slab doesn't. From the ASCE Texas guidelines:

  • Tilting posts or piers that no longer carry the floor straight down.
  • Rotting wood in beams, joists, or sills.
  • Supports spaced too far apart for the load, so floors sag between them.
  • Crawl space moisture from poor ventilation or drainage.
  • Lost void space, where soil or debris fills the gap the design needs under foundation elements.

How are pier and beam foundations repaired?

The guidelines list these repairs:

  1. Shimming. Hardwood or steel shims go on top of the pier caps to level the floor framing.
  2. Framing repairs. Damaged or weak beams and joists are replaced or reinforced, usually with treated lumber.
  3. Added supports. New piers or posts go in where spans are too long or old supports have failed.
  4. Restoring void space under foundation elements where the design calls for it.
  5. Crawl space moisture control. This includes cross ventilation, drainage, ground clearance for beams and joists, and treated lumber.

Because a crawl space gives access to the framing, pier and beam repairs can often be done from underneath the house.

What helps both kinds of foundations?

The ASCE Texas guidelines say non-structural steps can improve performance and reduce future movement. They suggest trying them, and monitoring the house, before or instead of structural repair when that makes sense:

  • Keep soil moisture near the foundation even on all sides, without overwatering.
  • Extend downspouts well past the foundation and any planting beds.
  • Grade the soil to slope away from the house. Where practical, the guidelines suggest a 5 percent slope (6 inches in 10 feet) for the first 10 feet all around the house.
  • Deal with trees and large shrubs near the house. Removing a tree can cause the soil to swell back, so engineers may recommend a waiting period before repairs.
  • Consider root barriers or moisture barriers.

Who should design the repair?

The ASCE Texas guidelines say evaluation and repair design should be done by a professional engineer holding a Texas license, and the engineer who seals the plans is the engineer of record. Fort Worth asks for engineered foundation plans and an engineer's letter with a foundation repair permit (Fort Worth submittal requirements). Our guide to foundation engineer reports explains what to expect and what to ask.

Common questions

How do I know if my house is pier and beam?

Look around the base of the outside walls for vent openings or a small access door into a crawl space. Inside, pier and beam floors are framed with wood joists, so they can feel a bit springy or sound hollow. A slab house has no crawl space, and the floor sits on concrete close to ground level.

Can I drill into a post-tensioned slab?

Not without checking first. Post-tensioned slabs hold steel cables under tension. ConcreteNetwork notes many are stamped to warn owners and contractors, and that a cut tendon is very difficult to repair. Have an engineer or a scanning company locate tendons before any cutting or coring.

What is shimming on a pier and beam house?

Shimming means adding hardwood or steel shims on top of the pier caps to bring floor framing back up to level. The ASCE Texas guidelines list it as a common pier and beam repair, along with fixing damaged framing and adding supports.

Why test plumbing after a slab is lifted?

Lifting a slab can stress the pipes under it. The ASCE Texas guidelines say water supply and drain lines should be tested for leaks when jacking or lifting is part of the repair, and any leaks found should be fixed.

Do both foundation types need an engineer for repairs?

The ASCE Texas guidelines say residential foundation evaluation and repair design should be done by a professional engineer holding a Texas license. Some cities, including Fort Worth, also ask for engineered plans with a foundation repair permit.

Sources

  1. Guidelines for the Evaluation and Repair of Residential Foundations, Version 3 (Texas Section ASCE, adopted April 1, 2022) (accessed Oct 8, 2026)
  2. Post-Tensioning Construction Basics (ConcreteNetwork.com) (accessed Oct 7, 2026)
  3. Houston Black, Texas State Soil (USDA NRCS fact sheet, hosted by Texas Water Development Board) (accessed Oct 7, 2026)
  4. Submittal Requirements for Residential Remodels (City of Fort Worth, rev. 05/27/2026) (accessed Oct 7, 2026)
  5. Texas Property Code Sec. 5.008, Seller's Disclosure of Property Condition (accessed Oct 7, 2026)

Have a leak, storm damage or a project in mind?

Free inspections and written estimates, with photos of what we find.