Updated Oct 8, 2026 by Apex Roofing & Construction. General information for North Texas homeowners, not legal or insurance advice.
Your attic is the space between your ceiling and your roof deck. In a North Texas summer it can get very hot. How well that heat and moisture get out has a lot to do with how long your shingles last and whether the shingle warranty holds up. Below we cover how attic ventilation works and what the building code asks for. Then we go over what to check on your own house.
Why do attics need ventilation?
Most homes here have a vented attic. Outside air flows through it to carry heat and moisture away. The Asphalt Roofing Manufacturers Association (ARMA) says excess heat on a roof speeds up the aging of roofing materials, raises attic temperature and can push heat into the living space. ARMA calls ventilation a highly effective way to lower roof temperatures, especially in hot climates.
Ventilation does three jobs, according to ARMA's ventilation bulletin:
- It removes heat that bakes shingles from below.
- It removes moisture that rises from the house and can condense on the cold underside of the deck in winter.
- It reduces ice dams in cold climates.
The third job matters little in Fort Worth. The city's own re-roofing FAQ says an ice barrier is not required here because the area has no history of ice damming. Heat and moisture are the real concerns.
How does a balanced system work?
ARMA describes it as the chimney effect. Hot air rises and leaves through exhaust vents near the ridge. Cooler outside air is pulled in through intake vents low on the roof, usually in the soffits under the eaves. Air has to come in to go out. A roof with lots of exhaust and almost no intake does not move much air.
ARMA's guidance:
- Intake should be about 50 to 60 percent of the total net free area, and exhaust about 40 to 50 percent.
- Intake should never be less than exhaust.
- Vents should be continuous along the eaves and ridge, or spaced evenly if they are individual vents.
"Net free area" is the open area air can actually pass through, after screens and louvers. Every vent product lists its rating on the package or spec sheet.
What does the building code require?
Fort Worth has adopted the 2021 International Residential Code with local amendments. Section R806 covers roof ventilation. In plain words, the 2021 IRC text says this.
- R806.1: Enclosed attics need cross ventilation, with openings protected from rain and screened against birds, rodents and snakes. Openings must be between 1/16 inch and 1/4 inch, or covered with a mesh in that range.
- R806.2: The minimum net free vent area is 1/150 of the vented attic area.
- The 1/300 exception: The minimum drops to 1/300 when not less than 40 percent and not more than 50 percent of the required vent area is in the upper part of the attic, no more than 3 feet below the ridge, measured vertically. The rest must be in the bottom one-third of the attic. The code adds a vapor retarder condition, but only for Climate Zones 6, 7 and 8. Texas counties fall in zones 2, 3 and 4, and Tarrant County is in zone 3, per the Texas A&M Energy Systems Laboratory, so that condition does not apply here.
- R806.3: Insulation and blocking cannot block soffit vents. There must be at least a 1 inch gap between the insulation and the roof deck at the vent.
- R806.4: Vents must be installed per the maker's instructions.
We checked the North Central Texas Council of Governments' recommended 2021 IRC amendments, which many DFW cities adopt, and found no change to Section R806. Your own city may have its own amendments, so check its code page.
What does that look like for a real house?
Take an attic with 1,500 square feet of floor area. One square foot is 144 square inches.
| Rule | Total vent area | Upper (exhaust) | Lower (intake) |
|---|---|---|---|
| 1/150 | 10 sq ft (1,440 sq in) | 4 to 5 sq ft (576 to 720 sq in), using ARMA's split | 5 to 6 sq ft (720 to 864 sq in), using ARMA's split |
| 1/300 with 40 to 50% up high | 5 sq ft (720 sq in) | 2 to 2.5 sq ft (288 to 360 sq in) | 2.5 to 3 sq ft (360 to 432 sq in) |
To size the vents, divide each number by the net free area printed for the product you plan to use. For example, a ridge vent is rated per linear foot, and a soffit vent is rated per piece or per foot. If the ridge on your house is too short to supply the exhaust you need, that changes the plan. Ask your roofer to show the math in writing.
What kinds of vents are there?
Intake vents
- Soffit vents. Continuous strips or individual vents under the eaves. The most common intake.
- Edge or rooftop intake vents. Used on homes without usable soffits.
Exhaust vents
- Ridge vents. A continuous vent along the peak, covered by cap shingles.
- Box or static vents. Square vents cut into the roof near the top.
- Turbines. Spinning vents that use wind to pull air.
- Gable vents. Louvered openings in the gable walls.
- Powered attic fans. Electric fans mounted on the roof or gable.
Why shouldn't you mix exhaust types?
ARMA warns that combining different types of exhaust vents over one attic space may cause short-circuiting. Picture a ridge vent next to a gable vent. The ridge vent can pull air in through the gable vent instead of from the soffits. The lower attic never gets fresh air. Pick one exhaust type for each attic space and pair it with enough intake.
Powered fans can cause a different problem. ENERGY STAR says that if soffit vents are blocked and the attic is not sealed from the house, an attic fan can pull cooled air up out of the house and raise your energy bill. ENERGY STAR also calls covering soffit vents with insulation the most common mistake homeowners make. Rafter baffles keep a clear channel open.
What about unvented, or sealed, attics?
Some homes use an unvented attic, often with spray foam under the roof deck. Section R806.5 allows this only when a list of conditions is met. The attic has to be completely inside the building's thermal envelope, and insulation rules depend on the type used. In Climate Zones 1 to 3, attics using air-permeable insulation need extra measures, such as a vapor diffusion port near the peak. A builder or design professional should make this call. It is a design decision, and it can't be done as a quick fix.
It can also affect your shingle warranty. The Owens Corning warranty described below excludes damage from unvented attics.
Does ventilation affect my shingle warranty?
Often, yes. Read the warranty for the exact shingle you buy. As one example, Owens Corning's Preferred Protection limited lifetime warranty, printed August 2026, says the roof must be installed over a ventilated roof deck. It lists damage caused by improper or inadequate roof ventilation, unvented attics or enclosed rafter assemblies among the things it does not cover. Our roof warranty guide explains how manufacturer and workmanship warranties differ.
What are the signs of poor attic ventilation?
- A very hot attic on a summer afternoon, much hotter than it feels outside.
- Insulation pushed against the soffits, with no baffles.
- Rust on nails, damp spots, or dark stains on the underside of the deck.
- Mold or a musty smell in the attic.
- Shingles that curl, blister or lose granules early.
- Very few vents, or a mix of exhaust types on one roof.
If you see these, an inspection can tell you whether the vents are short, blocked or mixed. Our guide to what a roof inspection includes covers what to ask for, and how long a roof lasts in Texas explains how heat ages shingles.
Common questions
How much attic ventilation does my house need?
Under 2021 IRC section R806.2, the minimum net free vent area is 1/150 of the vented attic area. It can drop to 1/300 if 40 to 50 percent of the required vent area is in the upper part of the attic, no more than 3 feet below the ridge, with the rest in the bottom third. For a 1,500 square foot attic that means 10 square feet at 1/150, or 5 square feet at 1/300.
Should I have more intake or more exhaust?
More intake, or at least equal. The Asphalt Roofing Manufacturers Association recommends about 50 to 60 percent intake and 40 to 50 percent exhaust, and says intake should never be less than exhaust. Too little intake can make exhaust vents pull air from the house instead of from outside.
Can I mix ridge vents with box vents or turbines?
It is not recommended over the same attic space. ARMA says combining different types of exhaust vents above a common attic can short-circuit the system, so air flows from one exhaust vent to another instead of coming in at the soffits.
Are powered attic fans a good idea in Texas?
Be careful with them. ENERGY STAR warns that if soffit vents are blocked and the attic is not sealed from the house, an attic fan can pull cooled air up out of your living space and raise energy use. Passive, balanced vents plus air sealing and insulation are the usual first step.
Can poor ventilation affect my shingle warranty?
Yes. For example, an Owens Corning limited lifetime warranty printed in August 2026 requires the roof to be installed over a ventilated deck and excludes damage caused by improper or inadequate ventilation. Read the exact warranty for the shingle you choose.
Sources
- ICC: 2021 International Residential Code, Chapter 8, Section R806 Roof Ventilation (accessed Oct 8, 2026)
- City of Fort Worth: Building and Energy Codes (2021 IRC with local amendments) (accessed Oct 8, 2026)
- NCTCOG: Recommended Amendments to the 2021 International Residential Code (approved July 2021, PDF) (accessed Oct 8, 2026)
- Asphalt Roofing Manufacturers Association: Attic space ventilation is key to cooling a roof (Oct 2023, PDF) (accessed Oct 8, 2026)
- Asphalt Roofing Manufacturers Association: Considerations in attic ventilation system selection (accessed Oct 8, 2026)
- City of Fort Worth: Residential Re-Roofing FAQ (PDF) (accessed Oct 8, 2026)
- ENERGY STAR: About attic ventilation (accessed Oct 8, 2026)
- Owens Corning: Preferred Protection Limited Lifetime Warranty, Pub. No. 10020609-P (Aug 2026, PDF) (accessed Oct 8, 2026)
- Texas A&M Energy Systems Laboratory: Texas building guide, climate zones by county (PDF) (accessed Oct 8, 2026)
