Updated Oct 8, 2026 by Apex Roofing & Construction. General information for North Texas homeowners, not legal or insurance advice.
If you collect a few foundation repair bids, you'll hear about pressed pilings, drilled piers, steel piers, helical piers, mudjacking and foam. Each salesperson may tell you their system is the one that works. Below, we explain how each method works and where it tends to fall short. We also compare rough costs. The engineering facts come from Texas sources, and the costs come from national price guides.
The two main references are the Texas Section of the American Society of Civil Engineers (ASCE) repair guidelines, Version 3, adopted in 2022, and papers from the Foundation Performance Association (FPA), a Houston group of engineers and contractors.
Who should pick the pier type?
An engineer. The ASCE Texas guidelines say evaluation and repair design should be done by a professional engineer who holds a Texas license. They also say repair plans should show the locations of the underpinning elements and their sizes, depths, material types and required strengths.
The guidelines add two points worth remembering:
- Underpinning part of a house does not improve the parts that were not underpinned.
- Lifting a slab is unlikely to make it perfectly level.
What words should I know first?
- Active zone. The upper layer of clay that swells and shrinks with the seasons. ASCE's Recommended Practice for foundation design says piers must reach below the active zone and be anchored to resist uplift (ASCE Recommended Practice).
- Skin friction. Support from soil gripping the sides of the pier.
- End bearing. Support from the soil or rock under the bottom of the pier.
- Refusal. For pressed piles, the FPA defines it as the point where the driving force exceeds the load to be supported (FPA-SC-08-1).
- Uplift. Swelling clay pushing the house up. The FPA says common repair piers are not tied to the grade beams, so they can't prevent uplift unless designed to (FPA-RC-01).
What are pressed concrete pilings?
These are short precast concrete cylinders stacked one on top of another and pressed into the ground with a hydraulic jack. The weight of the house is the reaction force.
- How common: At a 2014 FPA program, the committee chair described them as the most common method of lifting concrete foundations in Texas (FPA, May 2014).
- Size and depth: Typically 6 inch diameter cylinders about 12 inches long. In the Houston area, driven depths averaged 12 to 16 feet, with some much deeper.
- Support: Mostly skin friction.
- Limits: The FPA paper says these piles typically don't resist uplift or significant sideways loads, and depth varies from pile to pile with the weight above. If a pile can't get deep enough into stable soil, it may move with the seasons.
What are drilled concrete piers?
A hole is drilled, steel reinforcement goes in, and concrete is poured in place. The shaft can be straight, or have a wider base called a bell.
- Support: The FPA says most support comes from the bottom, with some skin friction along the shaft. The goal is support below the active zone.
- Common problems the FPA lists: too shallow, a poorly formed bell, soil collapsing into the hole, poor drainage, and gaps around the shaft that let water reach deeper soil.
- About bells: The FPA's 2017 design paper on drilled piers in expansive soil found bells offer little resistance against upward movement and would not typically be needed for lightly loaded foundations (FPA-SC-16-0). That paper is about design, so ask your engineer how it applies to a repair.
What are steel push piers?
Also called resistance piers or steel pipe piles. Steel pipe sections are pressed into the ground one after another, again using the house's weight, until they reach the needed resistance or hit rock or another load-bearing layer.
- Support: Skin friction, unless pushed down onto rock or firm soil.
- Common problems the FPA lists: not pushed to refusal, installed at the wrong angle, overloaded, too little house weight to drive them deep enough, and brackets not clamped right after driving.
What are helical piers?
A steel shaft with screw-like plates, called helixes, is turned into the soil with hydraulic equipment. The FPA describes it as an end-bearing anchor driven to the torque needed for the required capacity.
- How capacity is checked: A Hubbell CHANCE engineer explains that installation torque is multiplied by a factor tied to the shaft size to estimate capacity. Load testing is the most accurate check but the most expensive (Hubbell).
- Does not depend on house weight to install, unlike pressed systems.
- Common problems the FPA lists: spacing too wide, wrong angle, not enough torque or depth below the active zone, and weak bracket connections.
Are mudjacking and foam injection the same as piers?
No. They lift and fill under the slab instead of reaching deeper soil.
- Mudjacking pumps a slurry of materials such as sand, fly ash or topsoil and cement under the slab. Foam injection uses an expanding urethane foam (FPA-RC-01).
- The FPA calls both shallow repair systems affected by active, moving soil. It also warns injected material can enter cracked utility lines and plug them.
- ASCE says grouting gives continuous support without much lift, mudjacking adjusts elevations, and either can be temporary on shallow footings or long-term on deep piers. It should not be done under underpinned foundations if expected soil swelling could damage the house.
How are pier and beam floors repaired?
ASCE lists shimming the floor framing on top of existing supports with hardwood or steel shims, repairing framing, adding supports, and restoring void space. Any added supports should be compatible with the original support system. See slab vs pier and beam.
How do the methods compare?
| Method | Installed by | Main support | Watch for | Cost tier |
|---|---|---|---|---|
| Pressed concrete pilings | Jacking against house weight | Skin friction | Shallow refusal, no uplift resistance | About $1,000 per pier |
| Drilled concrete piers | Drilling and pouring | Bottom, some side friction | Depth, bell quality, water in shaft | Varies with depth |
| Steel push piers | Jacking against house weight | Side friction or firm layer | Enough weight to drive deep | About $2,000 per pier |
| Helical piers | Screwed in with hydraulic drive | Helix plates (end bearing) | Torque, depth, brackets | About $3,000 per pier |
| Mudjacking or foam | Injection under slab | Shallow soil | Moving clay, plugged lines | $500 to $1,300 per job |
Per-pier figures are national estimates from Angi, updated Jul 9, 2026. Mudjacking is from HomeAdvisor, updated Jun 20, 2026. Our foundation repair cost guide has more.
What should I ask my engineer?
- Which pier type do you recommend here, and why not the others?
- What minimum depth should the piers reach, and how will that be checked?
- Is uplift from swelling clay a concern on this house?
- Will the slab be lifted, and will plumbing be tested before and after?
- Will you inspect during the work and take new floor elevations afterward?
An engineer's report should answer most of these before you sign a repair contract.
Common questions
What is the most common foundation pier in Texas?
A 2014 Foundation Performance Association program described precast concrete segmented piles, often called pressed pilings, as the most common method of lifting concrete foundations in Texas. They are short concrete cylinders stacked and pressed into the ground using the weight of the house.
Are steel piers better than concrete piers?
Not automatically. Each type has known ways to fail, and the right choice depends on soil, loads, depth to firm soil, and the house. The Foundation Performance Association lists failure modes for every common system. Let an independent engineer choose and specify the type and depth.
What does 'driven to refusal' mean?
For pressed piles, it is the point where the force needed to push the pile deeper exceeds the load it will carry, so the house starts to rise instead. Because the house's weight does the pushing, refusal depth varies from pier to pier.
Is mudjacking or foam a permanent foundation fix?
They lift and fill under a slab, but the Foundation Performance Association calls both shallow repairs affected by the active, moving soil. The ASCE Texas guidelines say this kind of support can be temporary on shallow footings or long-term on deep piers.
Do bell-bottom piers stop a slab from heaving?
Not by themselves. The Foundation Performance Association says repair piers that are not tied to the grade beams can't prevent uplift from swelling clay. Its 2017 paper on drilled piers also found bells add little resistance against upward movement.
Sources
- Guidelines for the Evaluation and Repair of Residential Foundations, Version 3 (Texas Section ASCE, adopted April 1, 2022) (accessed Oct 8, 2026)
- Recommended Practice for the Design of Residential Foundations, Version 2 (Texas Section ASCE, adopted Oct 4, 2007) (accessed Oct 8, 2026)
- FPA-RC-01-0, Post Foundation Repair Performance of Residential and Other Low-Rise Buildings on Expansive Soils (Foundation Performance Association, Jan 26, 2004) (accessed Oct 8, 2026)
- FPA-SC-08-1, Design, Manufacture, and Installation Guidelines of Precast Concrete Segmented Piles for Foundation Underpinning (Foundation Performance Association, Mar 5, 2014) (accessed Oct 8, 2026)
- FPA May 2014 program summary, precast concrete segmented piles (Foundation Performance Association) (accessed Oct 8, 2026)
- FPA-SC-16-0, Design Procedure for Drilled Concrete Piers in Expansive Soil (Foundation Performance Association, Nov 17, 2017) (accessed Oct 8, 2026)
- 3 Methods to Determine Helical Pile Capacity (Gary L. Seider, PE, Hubbell CHANCE, Oct 1, 2020) (accessed Oct 8, 2026)
- Underpinning Foundation Cost (Angi, updated Jul 9, 2026) (accessed Oct 8, 2026)
- How Much Does Foundation Repair Cost? (HomeAdvisor, updated Jun 20, 2026) (accessed Oct 8, 2026)
